Did you know?

Yellow Cycle paused due to pinch sensor Object hitting pinch bar Clear object from pinch bar and hit reset key to resume cycle Red / Green System fault Low system voltage …App Notice: Pinch Detected at Startup (Power Cycle & Factory Reset) Regular Reset: Reverts to "Drawer Full" when bin inserted. When NO bin inserted, stays on Pinch Detected. What I've already done: Completely removed litter bin/bag. Didn't think it was the problem but worth a try. Complete disassembly/clean.Few steps: 1: Cut either the black or blue wire. 2: Get a 2k ohm resistor. (I didn't have any so I used a resistor and a potentiometer.) P.s. The litter robot sends 5v to the cat sensor and gets 0,9v back, therefore you need the 2k ohm resistor. 3: Make the pressure point where the cat sensor were placed, to a switch.Our family has had our LR3 for two years and are mostly in love with it. However, we've had another set of DFI & Pinch Sensors go bad this past week (our 2nd in the last year), which has me concerned about long-term viability of the unit. To LitterRobot's credit, their CS team has been great about identifying the issue and sending replacement ...Hey, all. About 9 months after the purchase of my litter robot 3 connect, I got the rapid yellow flash, telling me I had a fault in my pinch detector. After cleaning the metal bits failed, I ended up cutting the metal ends off and using a butt splice with an environmental seal to connect the 2 wires and bypass the pinch detector all together.Few steps: 1: Cut either the black or blue wire. 2: Get a 2k ohm resistor. (I didn't have any so I used a resistor and a potentiometer.) P.s. The litter robot sends 5v to the cat sensor and gets 0,9v back, therefore you need the 2k ohm resistor. 3: Make the pressure point where the cat sensor were placed, to a switch. The Litter Robot 4 is a bit “sleeker” and more modern-looking overall, though. It only comes in black and white, and the outside is glossier than Leo’s. ... Within a month of purchase and setup, the pinch faults began to occur …If you need to replace the pinch detect terminals on your Litter-Robot and the unit is out of warranty, the process is simple and quick. For those who are th...Litter-Robot is equipped with anti-pinch sensors on both sides of the waste drawer chute to ensure your cat’s safety while in use. These sensors monitor for potential pinch conditions at all times. If your unit displays a green and white alternating light bar, this indicates an anti-pinch fault during power up. 1. geordi2. •. You can completely bypass (and cure) the pinch sensor issue with as little as a paperclip. All you need to do is unplug the two wire connector plugs from the aluminum …Pinch Fault Detected Help. I keep getting notifications from the Whisker App that my LR4 has a pinch detect fault. I cleaned the sensors, and made sure the carbon filter was …Hey, all. About 9 months after the purchase of my litter robot 3 connect, I got the rapid yellow flash, telling me I had a fault in my pinch detector. After cleaning the metal bits failed, I ended up cutting the metal ends off and using a butt splice with an environmental seal to connect the 2 wires and bypass the pinch detector all together.Litter Robot 3 not reversing during cycle. My Litter Robot 3 has been having a weird issue for the last two weeks. When it cycles, the globe rotates counter-clockwise until the hall sensor detects the magnet on the globe. It then stops, like it should. Then it's supposed to rotable clockwise to return to its home position, when the hall sensor ...Litter-Robot is equipped with Anti-Pinch Sensors on both sides of the Waste Drawer Chute to ensure your cat’s safety while in use. These sensors monitor for ...Removing the bonnet, flexing/bending back the latches (I discovered I wasn't properly seating the back clasps in-place, this helped a bit with the jerky spinning but failed to avoid the pinch detect fault) Emptied the tray, ensured the bag was installed properly. Emptied the litter entirely and replaced to ensure it's below the fill line. I’ve tried various litters, unscented, cat attract, regular litter box in different shapes, sizes, unclumping litter, pelleted litter, etc. He’ll use a puppy pad until it’s dirty, then the floor. ‍♀️ I thought this was a permanent issue, but I boarded him while we were gone a weekend and he used the box, not the pad, every.I have a litter robot 3 bought last year. It is now getting stuck in a cycle and is unusable. Symptoms are: A rotation cycle starts and dumps waste Then just before reversing direction the robot stops, the yellow light starts flashing and the globe moves a small amount further in the orginal rotation direction and stops A power off and restart …The damage should be visible on the left side under the pinch detect switch in the center of the DFI board where the opening is on the clear plastic shield. ... One thing I really like about litter robot is you Cabe but replacement parts for anythjg. ... Faulty tactile switch on my Erica Synths LXR-02.

The Litter-Robot four-part system (base, globe, bonnet, and drawer) was constructed with easy upkeep in mind. Whether you’re deep-cleaning or replacing a part, the simple modular design allows you to readily access and service your Litter-Robot. We also offer Litter-Robot repair services even after the WhiskerCare™ Warranty expires—just ...Need assistance with your Litter-Robot 4? Find guides & troubleshooting tips. Get the support you need today. ... Blue and white alternating light bar (Motor fault) Litter-Robot 4: Blue light bar flashing (Drawer full indicator "DFI" sensors) ... Litter-Robot 4: Yellow Ping-Pong Light Bar (Pinch Detect) Litter-Robot 4: Yellow Round Robin ...Ensure your cat did not enter Litter-Robot during the clean cycle. If your cat did enter, please press the reset button after use. Ensure the litter level doesn’t exceed the raised fill line. If there is too much litter, please remove enough to meet the fill line. Inspect bonnet tabs for corrosion or debris. Remove debris or corrosion if evident.To fix pinch detect on the litter robot, try cleaning the sensors and ensuring they are properly aligned. The litter robot is a popular self-cleaning litter box for cat owners. However, like any machinery, it can sometimes experience issues. One common problem is the pinch detect not working properly. This can result in the unit...

Tips and tricks for litter robot (pinch detect hack) Gives good tips. Also a very useful mod to protect pinch detect sensor. Final thing I’ll say, petroleum jelly on the metal connector for the pinch detect to help prevent corrosion. Mods, if you see this post please pin for future users to see. This is super useful!Led 5 - (Red) Wi-Fi - Fault Mode (Codes Pending) Unable to connect to router Verify router is powered up and operational Power cycle the robot Led 1 - (Blue) Battery mode enabled / Robot is in idle state Green / White Pinch sensor fault Cycle timed out Led 5 at Idle State Wi-Fi Mode (Leds 1-4 are blue) Alternate Single Led Codes Resets, OTA ...Litter-Robot is equipped with Anti-Pinch Sensors on both sides of the Waste Drawer Chute to ensure your cat’s safety while in use. These sensors monitor for ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. A firm, level surface is required for accurate d. Possible cause: Litter-Robot 3 flashing red light. A solid red light on your Litter-Robo.